Texas Instruments
La imagen puede ser una representación.
Consulte las especificaciones para obtener detalles del producto.
SN74LVC244APW
Ver Detalle Hojas de datos

SN74LVC244APW

Product Overview

  • Category: Integrated Circuit (IC)
  • Use: Buffer/Line Driver
  • Characteristics: Low Voltage, CMOS Logic, Octal Bus Buffer
  • Package: TSSOP (Thin Shrink Small Outline Package)
  • Essence: High-speed, low-power buffer with 3-state outputs
  • Packaging/Quantity: Tape and Reel, 2500 units per reel

Specifications

  • Supply Voltage Range: 1.65V to 5.5V
  • Input Voltage Range: 0V to VCC
  • Output Voltage Range: 0V to VCC
  • Maximum Operating Frequency: 80 MHz
  • Number of Channels: 8
  • Output Current: ±24 mA
  • Propagation Delay Time: 4.2 ns (typical)

Detailed Pin Configuration

The SN74LVC244APW has a total of 20 pins, which are distributed as follows:

  • Pin 1: Output 1 (Y1)
  • Pin 2: Output 2 (Y2)
  • Pin 3: Output 3 (Y3)
  • Pin 4: Output 4 (Y4)
  • Pin 5: Output 5 (Y5)
  • Pin 6: Output 6 (Y6)
  • Pin 7: Output 7 (Y7)
  • Pin 8: Output 8 (Y8)
  • Pin 9: Ground (GND)
  • Pin 10: Input 1 (A1)
  • Pin 11: Input 2 (A2)
  • Pin 12: Input 3 (A3)
  • Pin 13: Input 4 (A4)
  • Pin 14: Input 5 (A5)
  • Pin 15: Input 6 (A6)
  • Pin 16: Input 7 (A7)
  • Pin 17: Input 8 (A8)
  • Pin 18: Enable (G)
  • Pin 19: Supply Voltage (VCC)
  • Pin 20: Output Enable (OE)

Functional Features

The SN74LVC244APW is a high-speed octal buffer with 3-state outputs. It is designed to drive bus lines in a wide range of applications. The device operates at low voltage levels and offers compatibility with both TTL and CMOS logic levels. The 3-state outputs allow multiple devices to be connected to the same bus without any conflict.

Advantages and Disadvantages

Advantages: - High-speed operation - Low power consumption - Wide supply voltage range - 3-state outputs for bus sharing

Disadvantages: - Limited output current capacity - Not suitable for high-voltage applications

Working Principles

The SN74LVC244APW works by receiving input signals on its eight input pins (A1-A8) and amplifying them to the corresponding output pins (Y1-Y8). The enable pin (G) controls the operation of the device, while the output enable pin (OE) enables or disables the outputs. When the OE pin is high, the outputs are active, and when it is low, the outputs are in a high-impedance state.

Detailed Application Field Plans

The SN74LVC244APW is commonly used in various applications, including:

  1. Microprocessor/Controller Interfacing: It can be used to interface microprocessors or controllers with external memory or peripheral devices.
  2. Data Communication Systems: It is suitable for driving bus lines in data communication systems, such as UART, SPI, or I2C interfaces.
  3. Industrial Automation: The device can be utilized in industrial automation systems for signal buffering and level shifting.
  4. Automotive Electronics: It finds applications in automotive electronics for signal amplification and isolation.
  5. Consumer Electronics: The SN74LVC244APW is used in various consumer electronic devices, including TVs, audio systems, and gaming consoles.

Detailed and Complete Alternative Models

  1. SN74LVCH244A: Similar to SN74LVC244APW but operates at a higher voltage range (1.65V to 3.6V).
  2. SN74AHC244: A CMOS logic octal buffer with 3-state outputs, compatible with TTL levels.
  3. SN74HCT244: A high-speed CMOS octal buffer with 3-state outputs, suitable for mixed-voltage systems.

These alternative models offer similar functionality but may have different voltage ranges, speed characteristics, or package options.

Word count: 496 words

Enumere 10 preguntas y respuestas comunes relacionadas con la aplicación de SN74LVC244APW en soluciones técnicas

Sure! Here are 10 common questions and answers related to the application of SN74LVC244APW:

  1. Q: What is SN74LVC244APW? A: SN74LVC244APW is a type of integrated circuit (IC) commonly used as a buffer or line driver in digital electronic systems.

  2. Q: What is the purpose of using SN74LVC244APW in technical solutions? A: SN74LVC244APW is used to amplify or buffer digital signals, ensuring proper signal integrity and driving capability in various applications.

  3. Q: What voltage levels does SN74LVC244APW support? A: SN74LVC244APW supports voltage levels ranging from 1.65V to 5.5V, making it compatible with a wide range of digital systems.

  4. Q: How many channels does SN74LVC244APW have? A: SN74LVC244APW has 8 channels, allowing it to handle multiple input/output signals simultaneously.

  5. Q: Can SN74LVC244APW be used for bidirectional communication? A: Yes, SN74LVC244APW can be used for bidirectional communication by enabling its direction control pins.

  6. Q: What is the maximum data rate supported by SN74LVC244APW? A: SN74LVC244APW can support data rates up to 80 Mbps, making it suitable for high-speed digital applications.

  7. Q: Does SN74LVC244APW have any built-in protection features? A: Yes, SN74LVC244APW has built-in ESD protection on its inputs and outputs, safeguarding against electrostatic discharge.

  8. Q: Can SN74LVC244APW be cascaded to increase the number of channels? A: Yes, multiple SN74LVC244APW ICs can be cascaded together to increase the number of channels as per the application requirements.

  9. Q: What is the power supply voltage range for SN74LVC244APW? A: SN74LVC244APW operates with a power supply voltage range of 1.65V to 5.5V.

  10. Q: Are there any specific layout considerations when using SN74LVC244APW? A: Yes, it is recommended to follow proper PCB layout guidelines, including minimizing trace lengths and providing decoupling capacitors near the IC, to ensure optimal performance and signal integrity.

Please note that these answers are general and may vary based on specific application requirements.